FREE MAINLAND UK DELIVERY ON 97% OF PRODUCTS

FREE NEXT-DAY DELIVERY ON ELIGIBLE £90+ ORDERS

01952 370008

What Size LED Driver Do I Need? Calculator and Guide

What Size LED Driver Do I Need? Calculator and Guide

What size LED driver do I need? Multiply the strip’s watts per metre by its length, add 20% headroom, then round up to the next standard size. Match the voltage to the strip, 12V or 24V, and check the dimming method if you want to dim.

This guide gives you a free calculator, worked examples and a dimming compatibility table. It also covers voltage drop, IP ratings and the mistakes that cause flicker, buzzing and early failure.

Key takeaways

  • The formula: strip watts per metre × length × 1.2 gives the minimum driver watts.
  • Round up, never down: buy the next standard size above your result.
  • Voltage must match: a 12V strip needs a 12V driver, and a 24V strip needs a 24V driver.
  • Typical single-feed runs: about 5 m on 12V and about 10 m on 24V.
  • Dimming needs a matching system: triac, 0-10V, DALI, or a controller on the strip side.

What Does an LED Driver Do?

An LED driver is a power supply that turns mains AC into steady 12V or 24V DC. Anyone running LED strip from a socket needs one.

Shops also call it a transformer or a power supply. For strip, all three words mean the same part.

Strip is a constant-voltage load. Its own resistors set the current, so the driver only has to hold the voltage steady and supply enough watts.

Mains socket 230V AC LED driver 12V or 24V DC Controller optional LED strip sets the load

Three numbers describe any driver: output voltage, maximum watts and maximum current. The strip decides the voltage, and your calculation decides the watts.

What Size LED Driver Do I Need? Use the 20% Headroom Rule

Multiply watts per metre by length, add 20%, and round up to the next standard size.

Minimum driver watts = watts per metre × length in metres × 1.2
  1. Find the watts per metre on the product page or strip label. Common figures include 9.6 W/m and 14.4 W/m.
  2. Multiply by the strip length in metres to get the total load. With several strips, add their loads together.
  3. Multiply the total load by 1.2. That adds the 20% headroom.
  4. Round up to the next standard driver size, then confirm the voltage matches the strip.

Headroom stops the driver running at its limit. About 80% of the rating leaves a margin for heat and for strip you add later.

Round up, never down. An undersized driver can cause flicker, dimming or a strip that will not light.

What If the Label Does Not Show Watts per Metre?

Many labels list total watts for the reel, or the current in amps. You can still work out the figure.

  • Total watts for the reel: divide by the reel length in metres.
  • Amps: multiply by the strip voltage to get watts.
  • Only an LED count: ask the supplier or read the datasheet, rather than guessing.

A 5 m reel marked 48 W is 9.6 W/m. A strip rated 2 A at 24V is also 48 W.

How Do You Size a Driver for Several Strips?

Add the loads of every strip, then apply the 20% headroom to the total. All strips on one driver must share its voltage.

Wire each strip back to the driver in parallel, with its own feed. Do not join strips end to end beyond the single-feed limit.

One larger driver is neater. Several smaller drivers can shorten cable runs and keep some lights working if one driver fails.

The rule stays the same for any setup: calculate the load, add 20%, then choose the next size up.

LED Driver Wattage Calculator

Enter your strip details. The calculator returns the minimum watts, the standard size to buy and the voltage drop on your cable.

Enter your figures to see the result.

Results are a guide. Always check the strip label and the driver’s datasheet before you buy.

Worked Examples

These three examples use the formula from the previous section.

Setup Load With 20% headroom Driver to buy
5 m of 9.6 W/m strip, 24V 48 W (2 A) 57.6 W 60 W, 24V
5 m of 14.4 W/m strip, 12V 72 W (6 A) 86.4 W 100 W, 12V
Two 5 m strips of 9.6 W/m on one driver, 24V 96 W (4 A) 115.2 W 120 W, 24V

Common Driver Sizes and Current

Divide watts by volts to find the current a driver can supply. Sizes vary by range, so check the datasheet.

Driver size Maximum current at 12V Maximum current at 24V
30 W 2.5 A 1.25 A
60 W 5 A 2.5 A
100 W 8.3 A 4.2 A
150 W 12.5 A 6.25 A
200 W 16.7 A 8.3 A
300 W 25 A 12.5 A

The same wattage draws half the current at 24V. That is why 24V copes better with longer runs.

12V or 24V: Which LED Driver Should You Choose?

Choose the voltage printed on your strip. The driver must match it exactly, because a mismatch can damage the strip.

When 12V Makes Sense

A 12V LED driver suits short runs of about 5 m or less. Cabinets, shelves and TV backlights are typical examples. At that length, voltage drop is small.

When 24V Makes Sense

A 24V LED driver suits longer runs of up to about 10 m from one feed. It draws half the current for the same watts. Cove and room-perimeter lighting usually need 24V.

How Much Voltage Drop Is Too Much?

Voltage drop dims the far end of a strip. As a rule of thumb, keep it below about 5%, and nearer 3% where you can.

Take a 48 W strip on 24V. It draws 2 A. Over 10 m of 2.5 mm² cable, the round-trip drop is about 0.30V, or 1.2%.

Keep the driver close to the strip, use thicker cable, or feed long runs from both ends. Feeding power at extra points is called power injection.

Match the voltage first, then check the run length. Twelve volts suits short runs, and 24V suits long ones.

Do You Need a Dimmable LED Driver?

Only if you want to dim from the mains side. Otherwise, a non-dimmable driver with a controller on the strip side is simpler.

Dimming method Where it dims What you need Best for
Triac (phase-cut) Mains side Triac driver and an LED-rated wall dimmer Homes and retrofits
0-10V Separate control cable 0-10V driver and controller Commercial projects
DALI Digital control bus DALI driver and DALI controller Large or smart systems
PWM controller DC side, between driver and strip Non-dimmable driver and a matching controller Single-colour and colour-changing strip

“Dimmable” does not mean universally compatible. The driver, the dimmer and the strip must all use the same method.

Triac Dimmable Drivers

Triac drivers work with phase-cut wall dimmers, the type most homes already have.

  • Match the dimmer type. Some drivers need a trailing-edge dimmer, and a leading-edge dimmer can cause flicker or buzzing.
  • Check the dimmer’s minimum load. A strip that draws less than the minimum can flicker or drop out.
  • Avoid dimmers made for old incandescent bulbs. They often struggle with LED loads.

0-10V and DALI Drivers

A 0-10V driver takes a low-voltage control signal on separate wires. At 0V it dims to minimum, and at 10V it gives full output. A DALI driver takes digital commands and suits larger or smart systems.

A DALI controller will not dim a triac-only driver.

Dimming at the Strip with a Controller

A PWM dimmer or controller sits between a non-dimmable driver and the strip. It suits single-colour strip.

Colour-changing strip, including RGB, RGBW and RGBCCT, uses the same approach. Use a non-dimmable driver, because the controller does the dimming.

Choose a dimming method first, then buy the driver that supports it.

Plug-In or Hardwired: Which Driver Type Suits Your Install?

Choose a plug-in driver for simple installs, and a hardwired driver where it must be hidden or fixed in place.

  • Plug-in: it comes with a mains lead and plug, so you fit it near a socket. No mains wiring is needed.
  • Hardwired: it connects to the building’s mains supply. A qualified electrician should wire the mains input.
  • Low-voltage side: connecting the strip to the driver output is usually a DIY job for both types.

Wherever the driver sits, keep it close to the strip. Leave space for airflow, and make sure you can reach it later.

Plug-in suits most homes. Hardwired suits hidden or fixed installations.

Which IP Rating Does the Driver Need?

Use an IP20 driver in dry indoor spaces. Anywhere it can get wet, choose a driver with its own outdoor rating.

A waterproof strip does not make the driver waterproof. Check the driver’s label separately, or keep it in a dry, ventilated enclosure. 

What Mistakes Do People Make When Choosing a Driver?

  • Using a constant-current driver on strip: strip needs constant voltage. The label should show volts, not milliamps.
  • Boxing the driver in: drivers run warm, so leave space for air to move around them.
  • Adding strips later without rechecking: add the new load to the old one, then recalculate.
  • Reusing an old halogen transformer: many output AC, but strip needs DC. Check the label first.

Most driver faults come from a wrong type or a wrong size. Checking the label before you connect prevents both.

Ready to choose your driver?

Browse by voltage, then check the wattage against your calculator result.

Shop 12V drivers → Shop 24V drivers → View all drivers

Frequently Asked Questions

Can I use a bigger driver than the calculator suggests?

Yes. A larger driver is fine, because the strip only draws what it needs. Size up, never down.

Can I use a 24V driver on a 12V strip?

No. The voltage must match, and the wrong voltage can damage the strip.

Can one driver power several strips?

Yes, if they share the same voltage and the combined load plus headroom fits the driver. Wire the strips in parallel, not end to end.

What size LED driver do I need for 10 metres of strip?

For 14.4 W/m strip on 24V, the load is 144 W, or 172.8 W with headroom. Choose a 200 W driver, and feed the strip from both ends or as two 5 m runs.

Why does my strip flicker after fitting a new driver?

Besides sizing and dimmer problems, check for a loose connection or a failing driver. Test with the dimmer bypassed and the strip on a short cable.

Final Verdict

What size LED driver do I need? Work out the total watts, add 20%, and round up to the next standard size. Match the 12V or 24V rating to your strip. Keep the driver close to the strip. Use a dimming method that suits your dimmer or controller. Run the calculator above with your own figures, then browse drivers in the right voltage.